In a word: The Neumann classic. Three directional characteristics and switchable pre-attenuation ensure suitability for a wide range of applications. The U 87* is probably the best known and most widely used Neumann studio microphone. It is equipped with a large dual-diaphragm capsule with three directional patterns: omnidirectional, cardioid and figure-8. These are selectable with a switch below the headgrille. A 10 dB attenuation switch is located on the rear. It enables the microphone to handle sound pressure levels up to 127 dB without distortion. Furthermore, the low frequency response can be reduced to compensate for proximity effect. Applications The U 87 Ai condenser microphone is a large diaphragm microphone with three polar patterns and a unique frequency and transient response characteristic. Users recognize the microphone immediately by its distinctive design. It is a good choice for most general purpose applications in studios, for broadcasting, film and television. The U 87 Ai is used as a main microphone for orchestra recordings, as a spot mic for single instruments, and extensively as a vocal microphone for all types of music and speech. Acoustic features The U 87 Ai is addressed from the front, marked with the Neumann logo. The frequency response of the cardioid and figure-8 directional characteristics are very flat for frontal sound incidence, even in the upper frequency range. The microphone can be used very close to a sound source without the sound becoming unnaturally harsh. By means of a high-pass filter interferences through subsonic and low frequencies are reduced remarkably. Polar patterns The dual-diaphragm capsule is elastically mounted and protected by a large headgrille. A switch below the headgrille selects the three directional patterns: omnidirectional, cardioid and figure-8. A window above this switch shows the symbol of the selected characteristic. Electrical features The letter A in the name indicates a more recent generation, as compared to the U 87 i microphones that were built from 1967 to 1986. Modifications apply to the electronic components of the microphone only; the capsule remained unchanged. The present-day circuitry increases the operational headroom of the U 87 Ai by supplying the bias voltages for the capsule through a reduced resistance. The result is a higher sensitivity of 10 dB for identical sound pressure levels, and an improved S/N ratio of 3 dB. Filter and attenuation A switch located at the rear attenuates the sensitivity by 10 dB. When this switch is activated, the microphone accepts sound pressure levels up to 127 dB (equivalent to a sound pressure of 45 Pa) without distortion. An additional switch at the rear allows to change the microphone's cutoff frequency. This reduces low frequency interference directly at the input of the microphone amplifier. This setting also compensates for the unavoidable bass boost that occurs with all pressure gradient transducers when they are used at close distance (proximity effect). The cardioid characteristic maintains a smooth frequency response at a distance of 30 to 40 cm, the figure-8 characteristic even at a distance of 15 to 20 cm. Specifications Acoustical operating principle Pressure gradient transducer Directional pattern Omnidirectional, cardioid, figure-8 plus Frequency range 20 Hz ... 20 kHz Sensitivity at 1 kHz into 1 kohm 20/28/22 mV/Pa1) Rated impedance 200 ohms Rated load impedance 1 kohms Equivalent noise level, CCIR2) 26/23/25 dB1) Equivalent noise level, A-weighted2) 15/12/14 dB-A1) Signal-to-noise ratio, CCIR2) (rel. 94 dB SPL) 68/71/69 dB1) Signal-to-noise ratio, A-weighted2) (rel. 94 dB SPL) 79/82/80 dB1) Maximum SPL for THD 0.5%3) 117 dB (cardioid) Maximum SPL for THD 0.5% with preattenuation3) 127 dB Maximum output voltage 390 mV Dynamic range of the microphone amplifier (A-weighted) 105 dB Supply voltage (P48, IEC 61938) 48 V ± 4 V Current consumption (P48, IEC 61938) 0.8 mA Matching connectors XLR3F Weight 500 g Diameter 56 mm Length 200 mm Caution: Shockmount EA 87 sold separately

In a word: The Neumann classic. Three directional characteristics and switchable pre-attenuation ensure suitability for a wide range of applications. The U 87* is probably the best known and most widely used Neumann studio microphone. It is equipped with a large dual-diaphragm capsule with three directional patterns: omnidirectional, cardioid and figure-8. These are selectable with a switch below the headgrille. A 10 dB attenuation switch is located on the rear. It enables the microphone to handle sound pressure levels up to 127 dB without distortion. Furthermore, the low frequency response can be reduced to compensate for proximity effect. Applications The U 87 Ai condenser microphone is a large diaphragm microphone with three polar patterns and a unique frequency and transient response characteristic. Users recognize the microphone immediately by its distinctive design. It is a good choice for most general purpose applications in studios, for broadcasting, film and television. The U 87 Ai is used as a main microphone for orchestra recordings, as a spot mic for single instruments, and extensively as a vocal microphone for all types of music and speech. Acoustic features The U 87 Ai is addressed from the front, marked with the Neumann logo. The frequency response of the cardioid and figure-8 directional characteristics are very flat for frontal sound incidence, even in the upper frequency range. The microphone can be used very close to a sound source without the sound becoming unnaturally harsh. By means of a high-pass filter interferences through subsonic and low frequencies are reduced remarkably. Polar patterns The dual-diaphragm capsule is elastically mounted and protected by a large headgrille. A switch below the headgrille selects the three directional patterns: omnidirectional, cardioid and figure-8. A window above this switch shows the symbol of the selected characteristic. Electrical features The letter A in the name indicates a more recent generation, as compared to the U 87 i microphones that were built from 1967 to 1986. Modifications apply to the electronic components of the microphone only; the capsule remained unchanged. The present-day circuitry increases the operational headroom of the U 87 Ai by supplying the bias voltages for the capsule through a reduced resistance. The result is a higher sensitivity of 10 dB for identical sound pressure levels, and an improved S/N ratio of 3 dB. Filter and attenuation A switch located at the rear attenuates the sensitivity by 10 dB. When this switch is activated, the microphone accepts sound pressure levels up to 127 dB (equivalent to a sound pressure of 45 Pa) without distortion. An additional switch at the rear allows to change the microphone's cutoff frequency. This reduces low frequency interference directly at the input of the microphone amplifier. This setting also compensates for the unavoidable bass boost that occurs with all pressure gradient transducers when they are used at close distance (proximity effect). The cardioid characteristic maintains a smooth frequency response at a distance of 30 to 40 cm, the figure-8 characteristic even at a distance of 15 to 20 cm. Specifications Acoustical operating principle Pressure gradient transducer Directional pattern Omnidirectional, cardioid, figure-8 plus Frequency range 20 Hz ... 20 kHz Sensitivity at 1 kHz into 1 kohm 20/28/22 mV/Pa1) Rated impedance 200 ohms Rated load impedance 1 kohms Equivalent noise level, CCIR2) 26/23/25 dB1) Equivalent noise level, A-weighted2) 15/12/14 dB-A1) Signal-to-noise ratio, CCIR2) (rel. 94 dB SPL) 68/71/69 dB1) Signal-to-noise ratio, A-weighted2) (rel. 94 dB SPL) 79/82/80 dB1) Maximum SPL for THD 0.5%3) 117 dB (cardioid) Maximum SPL for THD 0.5% with preattenuation3) 127 dB Maximum output voltage 390 mV Dynamic range of the microphone amplifier (A-weighted) 105 dB Supply voltage (P48, IEC 61938) 48 V ± 4 V Current consumption (P48, IEC 61938) 0.8 mA Matching connectors XLR3F Weight 500 g Diameter 56 mm Length 200 mm Caution: Shockmount EA 87 sold separately

In a word: The Neumann classic. Three directional characteristics and switchable pre-attenuation ensure suitability for a wide range of applications. The U 87* is probably the best known and most widely used Neumann studio microphone. It is equipped with a large dual-diaphragm capsule with three directional patterns: omnidirectional, cardioid and figure-8. These are selectable with a switch below the headgrille.A 10 dB attenuation switch is located on the rear. It enables the microphone to handle sound pressure levels up to 127 dB without distortion.Furthermore, the low frequency response can be reduced to compensate for proximity effect.ApplicationsThe U 87 Ai condenser microphone is a large diaphragm microphone with three polar patterns and a unique frequency and transient response characteristic.Users recognize the microphone immediately by its distinctive design. It is a good choice for most general purpose applications in studios, for broadcasting, film and television.The U 87 Ai is used as a main microphone for orchestra recordings, as a spot mic for single instruments, and extensively as a vocal microphone for all types of music and speech.Acoustic featuresThe U 87 Ai is addressed from the front, marked with the Neumann logo. The frequency response of the cardioid and figure-8 directional characteristics are very flat for frontal sound incidence, even in the upper frequency range. The microphone can be used very close to a sound source without the sound becoming unnaturally harsh. By means of a high-pass filter interferences through subsonic and low frequencies are reduced remarkably.Polar patternsThe dual-diaphragm capsule is elastically mounted and protected by a large headgrille. A switch below the headgrille selects the three directional patterns: omnidirectional, cardioid and figure-8. A window above this switch shows the symbol of the selected characteristic.Electrical featuresThe letter A in the name indicates a more recent generation, as compared to the U 87 i microphones that were built from 1967 to 1986. Modifications apply to the electronic components of the microphone only; the capsule remained unchanged.The present-day circuitry increases the operational headroom of the U 87 Ai by supplying the bias voltages for the capsule through a reduced resistance. The result is a higher sensitivity of 10 dB for identical sound pressure levels, and an improved S/N ratio of 3 dB.Filter and attenuationA switch located at the rear attenuates the sensitivity by 10 dB. When this switch is activated, the microphone accepts sound pressure levels up to 127 dB (equivalent to a sound pressure of 45 Pa) without distortion.An additional switch at the rear allows to change the microphone's cutoff frequency. This reduces low frequency interference directly at the input of the microphone amplifier.This setting also compensates for the unavoidable bass boost that occurs with all pressure gradient transducers when they are used at close distance (proximity effect).The cardioid characteristic maintains a smooth frequency response at a distance of 30 to 40 cm, the figure-8 characteristic even at a distance of 15 to 20 cm. SpecificationsAcoustical operating principle Pressure gradient transducerDirectional pattern Omnidirectional, cardioid, figure-8 plusFrequency range 20 Hz ... 20 kHzSensitivity at 1 kHz into 1 kohm 20/28/22 mV/Pa1)Rated impedance 200 ohmsRated load impedance 1 kohmsEquivalent noise level, CCIR2) 26/23/25 dB1)Equivalent noise level, A-weighted2) 15/12/14 dB-A1)Signal-to-noise ratio, CCIR2) (rel. 94 dB SPL) 68/71/69 dB1)Signal-to-noise ratio, A-weighted2) (rel. 94 dB SPL) 79/82/80 dB1)Maximum SPL for THD 0.5%3) 117 dB (cardioid)Maximum SPL for THD 0.5% with preattenuation3) 127 dBMaximum output voltage 390 mVDynamic range of the microphone amplifier (A-weighted) 105 dBSupply voltage (P48, IEC 61938) 48 V ± 4 VCurrent consumption (P48, IEC 61938) 0.8 mAMatching connectors XLR3FWeight 500 gDiameter 56 mmLength 200 mmCaution: Shockmount EA 87 sold separately

In a word: The Neumann classic. Three directional characteristics and switchable pre-attenuation ensure suitability for a wide range of applications. The U 87* is probably the best known and most widely used Neumann studio microphone. It is equipped with a large dual-diaphragm capsule with three directional patterns: omnidirectional, cardioid and figure-8. These are selectable with a switch below the headgrille.A 10 dB attenuation switch is located on the rear. It enables the microphone to handle sound pressure levels up to 127 dB without distortion.Furthermore, the low frequency response can be reduced to compensate for proximity effect.ApplicationsThe U 87 Ai condenser microphone is a large diaphragm microphone with three polar patterns and a unique frequency and transient response characteristic.Users recognize the microphone immediately by its distinctive design. It is a good choice for most general purpose applications in studios, for broadcasting, film and television.The U 87 Ai is used as a main microphone for orchestra recordings, as a spot mic for single instruments, and extensively as a vocal microphone for all types of music and speech.Acoustic featuresThe U 87 Ai is addressed from the front, marked with the Neumann logo. The frequency response of the cardioid and figure-8 directional characteristics are very flat for frontal sound incidence, even in the upper frequency range. The microphone can be used very close to a sound source without the sound becoming unnaturally harsh. By means of a high-pass filter interferences through subsonic and low frequencies are reduced remarkably.Polar patternsThe dual-diaphragm capsule is elastically mounted and protected by a large headgrille. A switch below the headgrille selects the three directional patterns: omnidirectional, cardioid and figure-8. A window above this switch shows the symbol of the selected characteristic.Electrical featuresThe letter A in the name indicates a more recent generation, as compared to the U 87 i microphones that were built from 1967 to 1986. Modifications apply to the electronic components of the microphone only; the capsule remained unchanged.The present-day circuitry increases the operational headroom of the U 87 Ai by supplying the bias voltages for the capsule through a reduced resistance. The result is a higher sensitivity of 10 dB for identical sound pressure levels, and an improved S/N ratio of 3 dB.Filter and attenuationA switch located at the rear attenuates the sensitivity by 10 dB. When this switch is activated, the microphone accepts sound pressure levels up to 127 dB (equivalent to a sound pressure of 45 Pa) without distortion.An additional switch at the rear allows to change the microphone's cutoff frequency. This reduces low frequency interference directly at the input of the microphone amplifier.This setting also compensates for the unavoidable bass boost that occurs with all pressure gradient transducers when they are used at close distance (proximity effect).The cardioid characteristic maintains a smooth frequency response at a distance of 30 to 40 cm, the figure-8 characteristic even at a distance of 15 to 20 cm. SpecificationsAcoustical operating principle Pressure gradient transducerDirectional pattern Omnidirectional, cardioid, figure-8 plusFrequency range 20 Hz ... 20 kHzSensitivity at 1 kHz into 1 kohm 20/28/22 mV/Pa1)Rated impedance 200 ohmsRated load impedance 1 kohmsEquivalent noise level, CCIR2) 26/23/25 dB1)Equivalent noise level, A-weighted2) 15/12/14 dB-A1)Signal-to-noise ratio, CCIR2) (rel. 94 dB SPL) 68/71/69 dB1)Signal-to-noise ratio, A-weighted2) (rel. 94 dB SPL) 79/82/80 dB1)Maximum SPL for THD 0.5%3) 117 dB (cardioid)Maximum SPL for THD 0.5% with preattenuation3) 127 dBMaximum output voltage 390 mVDynamic range of the microphone amplifier (A-weighted) 105 dBSupply voltage (P48, IEC 61938) 48 V ± 4 VCurrent consumption (P48, IEC 61938) 0.8 mAMatching connectors XLR3FWeight 500 gDiameter 56 mmLength 200 mmCaution: Shockmount EA 87 sold separately

In a word: The Neumann classic. Three directional characteristics and switchable pre-attenuation ensure suitability for a wide range of applications. The U 87* is probably the best known and most widely used Neumann studio microphone. It is equipped with a large dual-diaphragm capsule with three directional patterns: omnidirectional, cardioid and figure-8. These are selectable with a switch below the headgrille.A 10 dB attenuation switch is located on the rear. It enables the microphone to handle sound pressure levels up to 127 dB without distortion.Furthermore, the low frequency response can be reduced to compensate for proximity effect.ApplicationsThe U 87 Ai condenser microphone is a large diaphragm microphone with three polar patterns and a unique frequency and transient response characteristic.Users recognize the microphone immediately by its distinctive design. It is a good choice for most general purpose applications in studios, for broadcasting, film and television.The U 87 Ai is used as a main microphone for orchestra recordings, as a spot mic for single instruments, and extensively as a vocal microphone for all types of music and speech.Acoustic featuresThe U 87 Ai is addressed from the front, marked with the Neumann logo. The frequency response of the cardioid and figure-8 directional characteristics are very flat for frontal sound incidence, even in the upper frequency range. The microphone can be used very close to a sound source without the sound becoming unnaturally harsh. By means of a high-pass filter interferences through subsonic and low frequencies are reduced remarkably.Polar patternsThe dual-diaphragm capsule is elastically mounted and protected by a large headgrille. A switch below the headgrille selects the three directional patterns: omnidirectional, cardioid and figure-8. A window above this switch shows the symbol of the selected characteristic.Electrical featuresThe letter A in the name indicates a more recent generation, as compared to the U 87 i microphones that were built from 1967 to 1986. Modifications apply to the electronic components of the microphone only; the capsule remained unchanged.The present-day circuitry increases the operational headroom of the U 87 Ai by supplying the bias voltages for the capsule through a reduced resistance. The result is a higher sensitivity of 10 dB for identical sound pressure levels, and an improved S/N ratio of 3 dB.Filter and attenuationA switch located at the rear attenuates the sensitivity by 10 dB. When this switch is activated, the microphone accepts sound pressure levels up to 127 dB (equivalent to a sound pressure of 45 Pa) without distortion.An additional switch at the rear allows to change the microphone's cutoff frequency. This reduces low frequency interference directly at the input of the microphone amplifier.This setting also compensates for the unavoidable bass boost that occurs with all pressure gradient transducers when they are used at close distance (proximity effect).The cardioid characteristic maintains a smooth frequency response at a distance of 30 to 40 cm, the figure-8 characteristic even at a distance of 15 to 20 cm. SpecificationsAcoustical operating principle Pressure gradient transducerDirectional pattern Omnidirectional, cardioid, figure-8 plusFrequency range 20 Hz ... 20 kHzSensitivity at 1 kHz into 1 kohm 20/28/22 mV/Pa1)Rated impedance 200 ohmsRated load impedance 1 kohmsEquivalent noise level, CCIR2) 26/23/25 dB1)Equivalent noise level, A-weighted2) 15/12/14 dB-A1)Signal-to-noise ratio, CCIR2) (rel. 94 dB SPL) 68/71/69 dB1)Signal-to-noise ratio, A-weighted2) (rel. 94 dB SPL) 79/82/80 dB1)Maximum SPL for THD 0.5%3) 117 dB (cardioid)Maximum SPL for THD 0.5% with preattenuation3) 127 dBMaximum output voltage 390 mVDynamic range of the microphone amplifier (A-weighted) 105 dBSupply voltage (P48, IEC 61938) 48 V ± 4 VCurrent consumption (P48, IEC 61938) 0.8 mAMatching connectors XLR3FWeight 500 gDiameter 56 mmLength 200 mmCaution: Shockmount EA 87 sold separately

Need to convert a digital multi-track signal to analog, or vice versa The new BEHRINGER ULTRAGAIN DIGITAL ADA8200 is sublimely easy to operate, fits neatly into a single rack space, and thanks to its MIDAS-designed Mic Preamps and integrated A/D and D/A converters you ll get optimal signal conversion without the slightest hint of distortion or signal deterioration! The ULTRAGAIN ADA8200 is the professional s edge. What's New The ADA8200 builds on the proud legacy of our ADA8000, which is one of our all-time, best-selling products. Now, you re probably thinking, If they sell so many ADA8000s, then why are they changing them The short answer we improved it, by upgrading to reference-class Cirrus Logic converters and MIDAS-designed Mic Preamps, making the ADA8200 the natural choice for musicians and audio engineers alike. The Technical Stuff Signal conversion in the ADA8200 takes place at either 44.1 or 48 kHz with 24-bit resolution. The ADAT inputs and outputs can be operated independently, as long as there is an identical wordclock signal. Frequency range is an ultra-wide 10 Hz - 24 kHz at a 48 kHz sampling rate. The Ins and Outs Connections are provided for balanced XLR and ¼ TRS, as well as unbalanced ¼ TS inputs. XLR line out connectors located on the rear panel provide either balanced or unbalanced connectivity. Digital I/O is handled via ADAT format TOSLINK optical sockets, which support up to 8 channels of data. Value You can trust all your digital ones and zeros to the ADA8200, at an ultra-affordable price that will amaze you. Order online or stop by your authorized BEHRINGER dealer today and expand your digital arsenal. Important Compatibility Information There is a known issue with the ADAT interface implementation of the MOTU 2408 audio interface that makes it incompatible with the ADA8000/ADA8200 under certain operating conditions. Users are advised to avoid the following configuration: The MOTU 2408 is connected to a MOTU PCI-424 card and operating in PCI Mode under computer control The ADA8000/ADA8200 SYNC option is set to SLAVE and the clock input is being supplied from the MOTU 2408 The optical output from the ADA8000 ADAT interface is connected to an ADAT input on the MOTU 2408