Especially for electric guitar- Output Power: 2 x 200 W @ 4 Ohm, 2x 100W bridged @ 8 Ohm: 1x 400W @ 8 Ohm- Class D dynamic circuit- Frequency range: 20 - 20,000 Hz- Protection: soft start, short-circuit, DC, overheating, overvoltage- Controls: on/ off, volume, high, low, mode (bridge/ parallel/ stereo), ground lift, limiter sensitivity- Line input: 2x XLR and 2x 6.3 mm jack- Speaker output: 2x speaker twist and 3x 6.3 mm jack- Dimensions (W x H x D): 482 x 44 x 244 mm

4 Outputs - adjustable from 9 to 18V- 2 of which can be connected together with a Y-cable (not included in delivery) and deliver up to 36 V output voltage- The maximum capacity of the 9 V outputs is 300 mA, the variable outputs 500 mA- Connections: Output 1-8: 9V DC @ 300mA (individually isolated) - Output 9-12: 6-18V DC @ 500mA (individually isolated)- Dimensions: (W x D x H) 193 x 70 x 30 mm- Weight: 400 g- Included cables: 12 pieces of 5.5 x 2.1 mm coaxial plugs to 5.5 x 2.1 mm coaxial plugs

Format: 9.5''/ 1 RU- Adjustable in 6 steps (100%, 70%, 50%, 35%, 25%, 18%)- Reduces the volume of a guitar speaker at full saturation of the tubes- Made for 16 Ohm loudspeakers- Bypass/ attenuator switch for fast switching between full and reduced output power- Input: 1x 6.3 mm jack socket- Output for loudspeaker 1x 6.3 mm jack socket in parallel- Output impedance: 16 Ohm

Portable Preamp- For acoustic string instruments with piezo and magnetic pickups- Three selectable basic sounds: Flat, Modern and Vintage- Input limiters, polarity selector and notch filters- 3-Band EQ with semi-parametric center control- Balanced XLR DI Out- Tuner output- Operation with 9 V battery or 9 V DC power supply (not included, suitable power supply available under Art.409939)- Dimensions (W x H x D) 100mm x 55mm x 100mm

Power Attenuator- Reactive power reducer and load box with a finely tuned analogue speaker simulator- Enables the sweet spot of the amplifier to be used at any volume and even without a speaker for silent practice or recording- 6 Sound settings for the speaker- 6 Sound settings for the line out- Controls: Speaker Attn, line EQ, speaker tone, mic in gain and tone, line out level and bland, aux in level, phones level- Push buttons: Amp to line out pre/post and tone hard/soft, ground lift- Switches: Line out FX loop dry/wet, re-amp out FX loop dry/wet, FX level pro/inst, mic pad, phase and 48 V phantom power on/off, speaker impedance 8/16 ohms- LED: Input level, output level, mic signal peak- Impedance: 8 or 16 ohms- Stereo aux input- Amplifier input: 6.3 mm jack- Headphone output- Speaker outputs: 2 x 6.3 mm jack- Line output: 6.3 mm jack- DI output: XLR- Solo foot switch: 6.3 mm jack- Power consumption: 1500 mA- Power supply via 9 V DC power supply unit (2.1 x 5.5 mm coaxial socket, centre negative) (included)- Dimensions (W x D x H): 334 x 274 x 108 mm- Weight: 6.6 kg

Material: aluminium- For up to 12 effects units- Height adjustable ( /- 15 mm)- Adjustable cross bars ( /- 100 mm)- A space-saving power supply bracket is on the underside- Dimensions (W x H x D): 605 x 70-85 x 305 mm- Weight approx.: 3.2 kg- Incl. padded softcase with accessory compartment, 3m hook fastening tape, 2x elastic bands for installing the power supply

Adjustable in 6 steps (100%, 70%, 50%, 35%, 25%, 18%)- Reduces the volume of a guitar speaker at full saturation of the tubes- Made for 8 Ohm or 2x 16 Ohm loudspeakers- Bypass/ attenuator switch for fast switching between full and reduced output power- Input: 1x 6.3 mm jack socket- Output for loudspeaker 2x 6.3 mm jack socket in parallel- Output impedance: 8 Ohm

Material: Powder coated aluminium- Adjustable crossbars- Height adjustable- Dimensions (HxWxD): 70-85 x 450 x 305 mm- Weight: 3.51 kg- Incl. padded carrying bag, approx. 2.5 m hook fastening tape, 2 elastic bands and an allen key

Switching system 2 amps to 1 cabinet with remote input- 1 Instrument input: 6.3 mm jack- 2 Outputs to the amp: 6.3 mm jack- 2 Outputs to speaker: 6.3 mm jack- Switchable GND / lift per channel- Toggle switch- Remote control connection for foot switch: 6.3 mm jack- External 9 V power supply with 130 mA- Input Impedance: 10 Mohm- Output Impedance: 10 kOhm- Dimensions: 222 x 44 x 175 mm

Multi Power Supply for Effect Pedals- Powerbar power supply with 8 outputs for Palmer Pedalbay 40- Can be completely and unobtrusively integrated into the pedal board by simply replacing the first crossbar- Output 1-6: 9V DC @ max. 300 mA (individually isolated)- Output 7-8: 9/12 / 18V DC @ max. 500 mA (individually isolated)- Max. Total power: 2000 mA- Power supply with a 12 V DC power adapter (included in delivery)- Dimensions (W x D x H): 450 x 50 x 24 mm- Weight: 650 g- Incldues cable from 5.5 x 2.1 mm coaxial connector to 5.5 x 2.1 mm coaxial connector: 5 pieces with a length of 16 cm and 9 pieces with a length of 60 cm

Combines the Palmer Pedalbay 40 with the Palmer WT PB 40 power supply unit- Material: Aluminium- Power supply outputs 1-6: 9V DC @ max. 300 mA (individually isolated)- Power supply outputs 7-8: 9/12/18V DC @ max. 500 mA (individually isolated)- Dimensions: (W x D x H): 450 x 305 x 70 mm- Weight: 3.8 kg- Included cable set, 2x black rubber straps, approx. 2.5 m hook-and-loop fastener and a gig bag

Palmer PWT 12 IEC; universal effects pedal power supply with USB; 2 outputs with adjustable voltage from 6 - 18 V; 12 individually isolated 9V DC hollow pin outputs with internal negative terminal; non-isolated 9V DC hollow pin output with 2000mA; short-circuit and overload protection for each individual output; connections: Output 1-2: 6 - 18 V (250 mA max), Output 3-6: 9 V (100 mA max), Output 7-10: 9 V (250 mA max), Output 11-12: 9 V (500 mA max), Non-isolated DC output 9 V (2000 mA max), USB-C and USB-A outputs with charging power up to 18 W; Max. Output power 36 W; Max. Power consumption 54 W; Controls: Power switch, output voltage selector and switch; Includes: power cord, 15x DC cables (30 / 60 / 90 cm), 4x rubber feet; Dimensions: (W x D x H) 168 x 93 x 42 mm; Note: Ambient temperature (operating) 0 - 40 °C, Relative humidity

Pedalboard for Effect Pedals- Combines the Palmer Pedalbay 60 and the Palmer WT PB 60 Power Supply with 8 outputs- The power supply can be exchanged and fixed with the rear rail of the Pedalbay60- Material: Aluminium- Dimensions (W x D x H): 605 x 305 x 70 mm- Weight: 4.5 kg- Incl. cable set, 2x black rubber bands, approx. 3 m hook-and-loop fastening tape, gig bag- Power supply outputs 1-6: 9V DC @ max. 300 mA (individually isolated)- Power supply outputs 7-8: 9/12/18V DC @ max. 500 mA (individually isolated)

Material: Powder coated aluminium- Adjustable cross bars- Dimensions (H x W x D): 35 x 500 x 135 mm- Weight: 2.31 kg- Incl. Padded carrying bag, approx. 1.5 m hook-and-loop tape (self-adhesive) and 2 elastic bands- Correct power supply (Article Nr 357158 and 306177) not included

Power Supply for Effect Pedals- 6 Individually isolated 9 V DC outputs (300 mA each)- 2 Individually isolated 6 - 18 V DC (adjustable) outputs (max. 500 mA each)- Centre negative- Dimensions (W × H × D): 140 × 80 × 32 mm- Includes 18 V DC power supply

Material: powder coated aluminium- Adjustable crossbars- Height adjustable- Dimensions (H x W x D): 70-85 x 800 x 390 mm- Weight: 4.8 kg- Incl. padded carrying bag, approx. 5 m of hook-and-loop fastener tape, 2x elastic bands, and an allen key