Sonarworks SoundID Reference for Speakers & Headphones with Measurement Microphone (Box); speaker and headphone calibration software and measurement microphone in a bundle; precise adjustment of the frequency response to get flat and neutral sounding monitor speakers or headphones; enables a more precise evaluation of recordings and mixes; room analysis and automated calculation of the room size based on several measurements; Audio Calibration Engine allows for accurate processing; save an unlimited number of calibration profiles for monitor speakers; comes with headphone calibration profiles for more than 280 supported models; target curve custom adjustments in real time; Translation Check simulates over 20 different devices and device types for accurate mix translation results; three filter modes to choose from: Zero Latency, Mixed and Linear Phase allow to optimize filter quality and latency according to the monitoring situation; additional processing controls for Mono, Dry/Wet and Safe Headroom; App only: MIDI mapping for various controls and User Presets for predefined output device/channel pair combinations; measurement microphone with a pre-polarized electret-condenser capsule; frequency response: 20 - 20000 Hz with calibration curve; omnidirectional polar pattern; sensitivity: 14 mV/Pa; self noise: 24 dB; signal to nois ratio: 70 dB; dynamic range: 106dB; maximum sound pressure level: 132 dB SPL; requires: 48V phantom power; connector: 3 pin XLR; Microphone calibration file for 30° off-axis measurements in Sonarworks software native format to be used with SoundID Reference, Microphone calibration file for 0° on-axis measurements in .txt format

Sonarworks SoundID Reference for Speakers & Headphones with Measurement Microphone EDU (Box); Educational version: requires proof of eligibility; precise adjustment of the frequency response to get flat and neutral sounding monitor speakers or headphones; enables a more precise evaluation of recordings and mixes; room analysis and automated calculation of the room size based on several measurements; Audio Calibration Engine allows for accurate processing; save an unlimited number of calibration profiles for monitor speakers; comes with headphone calibration profiles for more than 280 supported models; target curve custom adjustments in real time; Translation Check simulates over 20 different devices and device types for accurate mix translation results; three filter modes to choose from: Zero Latency, Mixed and Linear Phase allow to optimize filter quality and latency according to the monitoring situation; additional processing controls for Mono, Dry/Wet and Safe Headroom; App only: MIDI mapping for various controls and User Presets for predefined output device/channel pair combinations; measurement microphone with a pre-polarized electret-condenser capsule; frequency response: 20 - 20000 Hz with calibration curve; omnidirectional polar pattern; sensitivity: 14 mV/Pa; self noise: 24 dB; signal to nois ratio: 70 dB; dynamic range: 106dB; maximum sound pressure level: 132 dB SPL; requires: 48V phantom power; connector: 3 pin XLR; Microphone calibration file for 30° off-axis measurements in Sonarworks software native format to be used with SoundID Reference, Microphone calibration file for 0° on-axis measurements in .txt format

Sonarworks SoundID Reference Measurement Microphone; measurement microphone; pre-polarized electret-condenser capsule; frequency response: 20 - 20000 Hz with calibration curve; omnidirectional polar pattern; sensitivity: 14 mV/Pa; self noise: 24 dB; signal to nois ratio: 70 dB; dynamic range: 106dB; maximum sound pressure level: 132 dB SPL; requires: 48V phantom power; connector: 3 pin XLR; Microphone calibration file for 30° off-axis measurements in Sonarworks software native format to be used with SoundID Reference, Microphone calibration file for 0° on-axis measurements in .txt format; 21-day trial of SoundID Reference available online

Micro de mesure - Capsule 6 mm à condensateur polarisé - Directivité: omnidirectionnelle - Réponse en fréquence: 20 Hz - 25 kHz (±2 dB) - SPL max: 140 dB - Nécessite une alimentation 18-52 V fantôme - Impédance de sortie: 200 Ohm - Plage dynamique 112 dB - Convient pour analyser, mesurer et tester en temps réel - Logiciels d'analyse spatiale - Fiche XLR mâle avec contacts plaqués or - Longueur: environ 150 mm - Bonnette fournie (WS-TM1) - Suspension antichocs (SMT-19) - Adaptateur d'étalonnage (TM1-CA) - Sensibilité individuelle et fichiers de données de calibration sur CD fourni

Microphone de mesure à condensateur Directivité: omnidirectionnel Champs libre Réponse en fréquence calibrée en cas d'utilisation avec ARC: 20 - 20 000 Hz ±0,5 dB Sortie sans transformateur Symétrisé électroniquement Impédance: 100 Ohm Rapport signal sur bruit: 65 dB (A) Niveau de pression acoustique maximum: 124 dB SPL Nécessite une alimentation fantôme: 12 - 48 V Dimensions: 129,5 mm x 23 mm Poids: 25 g Contenu de la livraison: microphone de mesure et pince micro

Micro de mesure à condensateur - Directivité: omnidirectionnelle - Réponse en fréquence: 20 - 20.000 Hz - Sensibilité: (@ 1 kHz) 43 dBV/Pa (7,1 mV / Pa) ±3 dB - Impédance: 800 Ohm - SPL: 94 dB / 128 dB max - Niveau de bruit équivalent: 22 dB pondéré A - Rapport signal sur bruit: 72 dB - Alimenté par piles (4x LR44 6V) - Poids: 150 g - Dimensions: 210 x 170 mm - Boitier métallique, finition champagne - Piles et pince fournies

Micro de mesure à condensateur - Pour système XL2 - Classe 2 - Réponse en fréquence (classe 1): 5 - 20.000 Hz - Directivité: omnidirectionnel - Impédance: 100 Ohm symétrique - SPL: 144 dB - Nécessite une alimentation Phantom +48V - Capsule amovible, membrane métalique - Longueur: 150 mm - Diamètre: 20,5 mm