Behringer CM1A

12

Module Eurorack

  • Interface MIDI vers CV
  • Convertisseur 16 bits
  • Fonctionnement monophonique et duophonique possible
  • 2 sorties CV
  • 2 sorties Gate
  • Commutable entre S-Trigger et V-Trigger
  • Port USB-B
  • MIDI In/Thru
  • Alimentation requise: 70 mA (+12 V) / 10 mA (-12 V)
  • Largeur: 6 HP
  • Profondeur: 52 mm
Référencé depuis Janvier 2022
Numéro d'article 523241
Conditionnement (UVC) 1 Pièce(s)
Largeur 6 TE / HP
75 €
Envoi gratuit et TVA incluse.
Disponible sous 2-3 semaines
Disponible sous 2-3 semaines

Le réassort de cet article devrait très prochainement avoir lieu, et pourra être expédié dès réception.

Informations sur l'expédition
1

12 Évaluations des clients

4.4 / 5

Vous devez être connecté afin de pouvoir évaluer un produit.

Note: Afin d’éviter que les évaluations de notre site soient polluées par des “ouï.dire”, des approximations ou encore de la publicité clandestine, nous autorisons uniquement nos clients à évaluer les produits achetés chez nous.

Une fois connecté, vous trouverez dans votre compte client, via le lien "Évaluer des produits", tous les articles que vous pouvez évaluer.

Utilisation

Caractéristiques

Qualité de fabrication

9 Commentaires

M
Efficace mais souvent perdu
MTRZ 18.04.2024
Il a tendance à se perdre dans certaines octaves hautes mais de manière général ça fonctionne plutôt bien pour le prix.
Utilisation
Caractéristiques
Qualité de fabrication
0
0
Signaler l'évaluation

Signaler l'évaluation

AW
USB/CV Gate
Ab Werk 12.02.2024
Un peu limité en octaves
Utilisation
Caractéristiques
Qualité de fabrication
0
0
Signaler l'évaluation

Signaler l'évaluation

google translate gb
Une erreur est malheureusement survenue, veuillez réessayer ultérieurement svp.
R
Nice MIDI-CV module. Make sure to calibrate it!
Radu7 25.02.2022
This module made a nice addition to my Behringer System 100 rack setup. Everything worked as designed save a few issues:

1. The Behringer Synthtribe 2.5.7 app constantly crashed and was unusable for configuring the CM1A. Going back to Synthtribe 2.5.5 worked perfectly. I reported the issue to Behringer so perhaps it will be rectified in the next release.

2. The scaling on the CM1A was terrible out of the box. It was unable to play two octaves in tune. This can be corrected using the calibration portion of the Synthtribe 2.5.5 app, but there are no instructions for this and Behringer support appear to be unaware this feature even exists. There is an incomplete diagram on the calibration page for the hookup to your DMM (you need a quality DMM with at least 3 decimal places of accuracy) and the process does not work well if you do not place a load (100KOhm resistor, for example) that approximates the impedance of the VCO you are calibrating the CM1A for.
After calibrating using Synthtribe with a suitable resistor across the DMM test leads it scales across 4 octaves quite well.

3. Does not play well with passive mults at all. This is common with any CV used for pitch control, but the CM1A is very sensitive to this when compared to other MIDI-CV modules I've tested. You need a buffered mult if you need to use the CV outs with more than one input each if you expect accurate scaling when controlling pitch.

None of the 'issues' I mentioned above are out of the ordinary for a MIDI-CV module in general, but could put off someone new to modular synths or cause them to return the module thinking it was faulty when it simply needed calibration, etc...
Utilisation
Caractéristiques
Qualité de fabrication
8
0
Signaler l'évaluation

Signaler l'évaluation

google translate gb
Une erreur est malheureusement survenue, veuillez réessayer ultérieurement svp.
S
TOP QUALITY
Sammysammy1 09.03.2022
Very easy to use and the quality is great
Utilisation
Caractéristiques
Qualité de fabrication
1
0
Signaler l'évaluation

Signaler l'évaluation